Frigidaire Oven F1 Beeping – Error Code Guide

by

What This Error Means

F1 on a Frigidaire oven means an electronic oven control (EOC) or keypad fault.
The control board thinks a key is stuck or its own circuitry is failing, so it locks the oven out and just keeps beeping.
Most of the time it is not the heating elements; it is the control system going crazy.

Official Fix

  • Kill power to the oven at the breaker for 1–2 minutes, then turn it back on.
    • If the F1 code clears and stays gone through a full bake cycle, it was a one-time glitch.
    • If F1 and the beeping come right back, the control or keypad has a hard fault.
  • Check the keypad on the front.
    • Press every button. Look for one that feels stuck, mushy, or does not click.
    • Wipe off any grease or spilled liquid. Use a slightly damp cloth only. No soaking, no spray directly into the panel.
    • If a button is physically jammed and you can free it, do that, restore power, and see if F1 is gone.
  • Disconnect power again before you touch anything inside.
    • Turn the breaker off. Verify the display is dead.
  • Access the control area.
    • Free-standing range: pull the stove out a bit and remove the back cover behind the control panel.
    • Wall oven: remove the trim and the screws holding the control panel, then tilt it forward.
  • Inspect wiring and connections.
    • Take a clear photo of all connectors first.
    • Look for burnt spots on the board, melted plugs, or loose connectors.
    • Push each plug firmly back onto the board. Do not bend the pins.
  • Check the oven temperature sensor (what the manual has you do).
    • Find the two small wires marked for the oven sensor on the control board.
    • Unplug that harness and measure the sensor with a multimeter at room temperature.
    • Normal Frigidaire sensor is roughly 1000–1100 Ω at room temp.
    • If it is open, shorted, or way off, replace the sensor first. A bad sensor can confuse the board and on some models can trigger F1.
  • If sensor and wiring check good, follow the official fix: replace the electronic oven control / user interface.
    • On some models the touchpad and control are one assembly. On others, you replace just the board or just the keypad.
    • Move each wire from the old board to the new one, one at a time, matching the photo you took.
    • Reassemble the panel, restore power, and test bake and broil. The F1 code should be gone.

The Technician’s Trick

  • Quick keypad vs board test (how pros avoid guessing).
    • Turn the breaker off. Panel must be dead.
    • Open the control area and find the flat ribbon cable from the keypad to the board.
    • Unplug that ribbon from the board. Leave everything else connected.
    • Stand clear of the live parts, then turn the breaker back on.
    • If F1 still pops up and it keeps beeping with the keypad unplugged, the control board itself is bad.
    • If the display sits quiet (no F1) with the keypad disconnected, the keypad / touch membrane is the problem.
    • Turn breaker off again before you plug the ribbon back in or touch anything.
  • Steam or spill fix that sometimes buys time.
    • If F1 started right after a boil-over or heavy cleaning, moisture may be inside the keypad.
    • Kill power. Open the control panel and let it air out with a fan for a few hours. Do not blast it with high heat.
    • This can dry a wet keypad and stop the F1 for a while, but if it comes back, expect to replace the keypad or board.

Is It Worth Fixing? (The Financial Verdict)

  • ✅ Fix: Oven under ~10–12 years old, otherwise in good shape, and you can get the control parts for under about $250–300.
  • ⚠️ Debatable: Oven 12–15 years old, needs other work (burners, door hinges, cracked knobs), or the control parts are hard to find or special-order.
  • ❌ Replace: Oven over 15 years old, glass top or cavity is damaged, or the quoted repair is more than ~50% of a decent new range.

Parts You Might Need